This purpose built motorcycle carrier has been built since 1999 and is the most over-designed model available! RV Motorcycle Carrier/ hitch rack, Class 3 or 4 hitch required(2" square receiver)for up to 900 lb capacity(quite often the hauling vehicle may be the limiting factor) This rack is for the larger and heavier motorcycles up to 87" long (wheel end to end).The tires shouldn't be wider than 210 mm or 8.50 to fit inside the tray. This carrier has a class 3(2 square) receiver hitch built into the end for towing vehicles up to 3500 lbs max. The hitch on the cycle carrier could be welded on or bolted on. All hardware for the bolt on attachment is included. THIS CARRIER CANNOT BE USED ON 5TH WHEEL OR TRAVEL TRAILER TYPE VEHICLES, THEY ARE RATED FOR 100-200 LBS TONGUE WEIGHT! They are used to demonstrate how the carrier works! These high quality, all steel units are manufactured in the US by motorcycleracks. THESE HITCH RACKS ARE THE ONLY CYCLE CARRIERS IN THIS CLASS WHERE THE DEVICE Deploys (2) vertical stabilizer bars to provide isolation from the vehicle and control the sway of the larger motorcycles for closer positioning to the vehicle plus improved ground clearance. Most of the competitors have the motorcycles sticking out there 5-13 more that is necessary and this tends to overload the vehicle! The motorcycle should be positioned as close as possible to the vehicle but never touch it for the best "drive-ability" possible.
The steel tray accommodates a few different types of motorcycles of different length for a near perfect balance of the carrier on the suv, van or truck!! The carrier is modular in design and is interchangeable for optimizing the set-up and for later upgrades/changes to the tray size and receiver bracket for adaptability on other vehicles. (in case you change hauling vehicle or cycle). Other accessories can be readily added later as you get experience with the carrier ie bolt on or magnetic lights and other stabilizer bars to simplify the tie down process. The dimension on the carrier shown here in all of the photos are: 14.75 and 19 (you have your choice of either dimension on the carrier) from hitch pin to center of cycle tray.
It is fully adjustable by moving the tray on the receiver assembly to the other bolt pattern available. Are inherently weighted toward the rear due to the rear engine mounting. To offset this weight and not overload the hitch by excess twist(torsion), the mounting position can be adjusted on the carrier by selecting the proper holes.The carrier comes complete with a 9-1/4" wide x 60" long loading ramp for a gentle incline. The receiver has the integrated anti-wobble/anti-tilt and a pair of cam lock style tie downs to strap the wheels to the tray.
The carrier consists of a heavy duty welded steel receiver assembly with side supports, main carrier tray measuring 8.25" wide x 84" long with front wheel chock, 2 vertical stabilizer bars, 1 horizontal sta-bar, and a loading ramp measuring 9.25" wide x 60" long. You add 2-4 tie downs. The integrated anti-chock/anti-tilt is guaranteed to work on ANY HITCH. (the anti-tilt collar type offered by others quite often do not work on many factory hitches including many GM factory hitches) THIS CARRIER ALSO HAS 4 HEAVY DUTY TIE DOWN POINTS, most of the competition usually offers 2.Tie down points with thin bracketry. Typical cycles that will fit on this carrier: Harley Davidson: Dyna/Super Glides, Older Fatbob, Softtail, Crossbones, all Dressers: ALL HD Softails w/200mm wide rear tires, BMW, Ducati, Honda GoldWings, VTX1300/1800, Suzuki HyaBussa, Suz Blvd, KawVulcans, Burgman 450&650, Honda St1300, DN-01 cruisers, VTX, Interceptors, Shadows, Nighthawks, CBR; Yamaha: FZ6, FV1-1100, Yam FJR1300, Vstars, etc. Send specific questions on your application: saslavick at yahoo dot com The questions will be answered within 1 day!
The only stock cycles this carrier will not take due to longer wheel bases and rear tires approx. 240mm and widerVictories and the Vrods/Wrods due to the excessively wide rear tires. THE ASSUMPTIONS FOR THESE BIKES TO FIT YOUR HAULING VEHICLE ARE: 1. Hitch height to ground is 14 or more and 2. The face of the hitch is flush to the end of the bumper of fascia(or the furthest protruding surface) +/- 1.I have a wide tray design for the newer HD Fatbobs or Suzuki Blvd with the 240mm rear tire and approx. 20mm 8.25 wide front. Just ask me about it.
For a technical and application website on these cycle carriers. VIDEO ON HOW TO LOAD THE BIG BIKES. The item "Motorcycle Hitch Carrier/Cycle Rack, Class 3/2 hitch on rack, 900 lb capacity" is in sale since Saturday, April 13, 2019. This item is in the category "eBay Motors\Parts & Accessories\Car & Truck Parts\Exterior\Towing & Hauling".The seller is "sslavick" and is located in Hagerstown, Maryland. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Barbados, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Gibraltar, Guadeloupe, Iceland, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Martinique, Maldives, Nicaragua, Oman, Peru, Paraguay, Reunion, Viet nam, Uruguay.